BLOG


Don't forget!

il 570xN.201984976

I don't make many repeatable pieces, simply because I don't like to make the same thing. But these forget-me-knot bow rings have been very popular, and I still enjoy making them, each one from scratch with sterling silver wire.

They are on sale for the next 7 days for $13 each (normally $18). Put BOWRING in the coupon code box at checkout for your discount. Tell your friends, share this post, they've never been on sale before!

https://www.etsy.com/listing/64339995/bow-ring-forget-me-knot-sterling-silver?ref=shop_home_active


El x


Custom mookaite ring

I love custom orders, though it makes me very nervous, creating to someone else's vision! But as long as the customer likes my existing work and style, and I keep within my capabilities, the outcomes are always happy ones. :D

I was asked if I had any more mookaite in lovely purpley/pinky/yellowy shades like this bracelet….

australian mookaite bracelet

Well, it just so happens that I did! I've got several slabs of mookaite sitting around - it's an Aussie stone and is reasonably easy to pick up at local rock shows.

So I showed her what I had left from the slab that the previous cabochon was cut from….

australian mookaite slab

She deemed it a-okay, colour-wise, and gave me an idea of where on the slab she'd like her cabochon cut from…

australian mookaite slab

This is what we decided on to get the maximum amount of the colours she wanted in the cab.

Next, to cut the cab. Cut cut cut……

australian mookaite cabochon

And we have a round cabochon of mookaite, approximately 30mm in diameter, and nigh on impossible to photograph due to the glossy finish that this awesome hard material takes.

Next, setting design. The lovely customer lady wanted a simple enough setting, with just a bit of embellishment - this was going to be a biggie anyways without any extra doodads hanging off the edges. So I did a few sketches of simple embellishments and she decided on cuts/lines at the points where the yellow vein in the stone reaches the edge. Just adds a bit of interest.

australian mookaite cabochon

And I liked the straight line that reached both edges to be sitting in a vertical position - this actually lines up with the edge of the finger when it's being worn, you'll see in the next picture.

So, next task, set the stone, 7mm band with a stripe cut on the band to echo the image in the stone. Oxidised, then cut back to a satin finish with high polish highlights.

australian mookaite sterling silver ring collage

Done. And off to its new owner on the other side of the world.

Phew.


El x

Snugs and mwahs

xo collage.jpg

Give your mamma a hug and a kiss this Mother's Day! 

These weighty little sterling silver pebble charms have been through a lot - formed by fire, handforged, smoothed and polished, handstamped, darkened and then polished up again - while still being organic and individual. 

Just like you, and your mum ;). 

Give us a kiss *pucker*.

In the shop, ready to ship here.



…..to finish

stone bezel soldering collage


Now that the stone has been cut and polished (did you miss seeing that, have a look here), it's time to set it into something wearable. After all, that's how I got into all this, because I wanted a way to show off these beautiful rocks and not just let them sit on the display shelf collecting dust.

I should point out before you read this that I'm entirely self-taught in metalwork. By self-taught, I mean that I haven't had any standardised training. I've learned how to do this from books, magazines, videos and the internet. And learning by trial and error. LOTS of trial and error. It's the long windy path of learning, and I often think (or rather, I know!) that if I did workshops and courses I would learn heaps of tricks of the trade that would ease my journey (and save me oodles of time and money). But I can't dedicate the time needed to coursework at this stage in my life, so I tinker away and read and research and voraciously consume all the information that I can find. So if you read this, and you are a metalsmith, please, feel free to point out an easier path, an alternative way, a better way for any of the steps! 

This is also not a 'how to'. I'm not endeavouring to teach anything here. This is simply a little peek into my process, for my customers and anyone else who might be even a little bit interested.

So, without any further ado….


PART 2 - FROM SHINY CABOCHON TO WEARABLE ROCK

queensland agate cabochon ready to be set

The previous post finished with the above piece of Queensland agate, all shiny and ready to collect dust on the display shelf. Nooo! Hurry, before my husband can nab it for his collection, I'd better get it into a wearable setting, quick smart! Onto the workbench it goes.


shape the bezel

First it needs a bezel. This goes around the stone and when the entire setting is finished, is pushed in and down and holds it firmly in place. Wrap the fine silver around the stone to get the measurements, cut it so that the ends meet true, and then they need to be joined together.


solder the bezel

To do that, it's off to the soldering station. That's where all the hot stuff is done and it's almost time to get the torch out (I love playing with fire, is there anyone out there who doesn't?). Onto the charcoal block, add some flux (that's the white paste on the silver there. It helps the solder run) and if you look closely, there's a teeny tiny piece of hard solder sitting under the join on that-there bezel.


solder the bezel 2

On with the torch, heat the joint and the solder flows along the seam, completely and securely closing it. Bezel closure - success! Quench in cool water, and pickle (a mild acid bath) to clean.


stone fits in the bezel

Check that the stone fits the newly-sealed bezel. Yup, it's nice and snug. If it isn't, it's back to the soldering station, heat again to unseal it, re-fit and do it all again. I've re-done more bezels than I can count. The fit is really really important. If it's too loose, the stone won't be secure. Too tight and, well, the stone doesn't fit in.

Next, we need a backplate. I played around with a few designs but because the stone's colours and patterning are so subtle and subdued, I chose the simplest of settings that gives the stone precedence. Because it's all about the stone here at Rocknwrap Central.


mark out the backplate

Mark out the backplate shape on a sheet of sterling silver. Yup, I can't draw for nuts.


saw pierce the back plate

And saw it out. I really enjoy sawing, it's very cathartic. I can't do very smooth lines yet, I need oodles more practice.


check fit of backplate and bezel

A pretty rough backplate sawn out (see what I mean about cruddy smooth lines and needing more practice?). Sit the bezel on the top to check it out, yep, it looks okay. Make sure the backplate and the bezel sit flush against each other, give them a gentle sand, and back to the soldering station it goes. 

Repeat above process - flux, heat, solder flows to seal the bezel to the backplate. Quench, pickle. check that the seal is complete. *sigh*… there's a bit I missed. Back to the torch, do it again…… 


soldered backplate and bezel

Better. The seam is sealed all the way around now. Phew. Check out how manky it looks after it's been fired. Don't fret, the pickle cleans that manky away.


check stone fit in setting

Check the stone fits and that I didn't warp the bezel before soldering it down. Done that too, all it takes is a little bump, fine silver is so soft. Nope, this time it's good. The stone fits like a dream. Oh, and that thread? It's part of my design. Just kidding, it's dental floss, it means that I can lift the stone in and out of the setting while I'm checking the fit without it getting stuck in there. Most stones can't handle heat (especially the temperatures that soldering torches get to) so all the soldering needs to be done before the stone gets set. 

Continuing on….


file shape setting edges

Get the files and sandpaper out and clean up that dodgy sawing. That's a better teardrop shape and the edge is silky and smooth to touch. It's deliberately slightly wonky as the cabochon is freeform and is a little bulgy to one side. So the backplate echoes the shape of the stone.

Now, how are we going to hang this pendant? Did I mention it's a pendant? It's a pendant. Possibly should have mentioned that before. Oh, and while we're mentioning things I've forgotten, I should possibly stamp the back before it's too late.

stamp backplate with sterling and maker’s mark

Stamp, stamp, stamp. 

stamped setting

There, 'sterling', because that's the metal (though the bezel is fine silver). r n w because that's me. I'm almost managing to stamp the suckers straight these days. 

So, if it's a pendant, it's going to need a bail to hang the chain through. I'm currently enjoying making hidden bails at the back so that the chain appears to be incorporated into the design, rather than just having a chain with a pendant dangling below it. So, where's my scrap pile?

scrap sterling for bail

Rummage, rummage, ah, here's a likely candidate for a bail. File the edges until it's a nice smooth pointy oval type shape. Bend, hammer, tap, manipulate, a bit of swearing, and lo….


shaped bail

….a lovely little bail. That will sit on the back of the pendant like…...

fit bail to setting

……this. Back to the soldering station to fix this on.

solder bail to setting

More flux, solder that bail top and bottom so that it's secure. 

quench after soldering

Quench in cool water because that metal is scorching!

pickle after soldering

Pickle in my high tech pickle pot (aka $12 coffee dripolator from Kmart). 

Check the solder joints and make sure that bail is secure. Because if it ain't, it's back I go.. (rinse, repeat, rinse, repeat).

It's secure. Things are going quite swimmingly today.

Now, the pieces are securely afixed. It's now time to sand, pre-polish and polish before setting the stone. This takes me a considerable amount of time before I've got it to a point where I'm happy to consider setting the stone. And a great deal of my frustration comes from this….


fire scale firestain on sterling silver

See that pinkish stain on the sterling silver? That's firescale. Sterling silver has a certain percentage of copper in its makeup, and this pink stain? It's the copper, rearing its ugly head on the surface.

I hate thee, firescale. I find some, sand it off, get to pre-polish and then I find some more. It seems to only show up in certain lights. It's a sneaky little devil, but rest assured, if I don't find it all and sand it off, it will show up at the final polish. And then back several steps I have to go - sand, pre-polish, polish again. Firescale and I, we're on the outs. But I will sand and sand until I have defeated e-v-e-r-y single bit. Because  a pink shadow on white silver is not my cup of tea.

tripoli polish on sterling silver

Right, firescale gone (I think), off to the tripoli wheel. This is the 'pre-polish', the final step before final polish. Yep, firescale all gone this time, this step would show any up if I'd missed it. 

Now, what to decide on finish for this pendant? 

I think a satin finish would be lovely for the front and back. I particularly like to finish the back in satin. It's such a big flat surface that fingerprints seem to multiply on it like magic. A satin finish sorts this out, but still leaves the silver finish silvery. The front gets a satin treatment too (I've got a fabulous wheel on my buffing machine that looks a bit like scotchbrite that delivers a great satin finish), but I like to bring the edges back up to a high polish. For contrast. I like a little contrast. Life is dull without it.

The setting is polished. Now, and only now, can I set the stone.

unset stone in setting

Pop the stone into the finished setting. Now it's time to push the bezel over to keep the stone secure.


push bezel over

Push, push, push. Poke prod. Slow and steady wins the race. 

bezel set queensland agate

There, the stone is secure in the setting. But to really stop the stone from wobbling and to give a polished finish, I need to burnish the top of the bezel.

burnish the bezel

Rub, rub, rub. The highly polished steel of the burnisher (that pointy thing I'm holding) rubbed against sterling silver creates a highly polished finish. Round and round and round we go until the whole bezel edge looks like….

burnish the bezel edge

…this. Can you see it, that shiny edge? I've still got some work to do yet though. 

Rub, rub, rub. 

There, finished.

satin finish on sterling silver back

Check the back. Nice satin finish. Hmm, there's a bit of grub on the side of that bail, still some cleaning to do.

I'll do that in a minute, time to organise the chain. And a chain needs a clasp of some description. I like to make a handmade clasp if the design suits one.


handmade sterling silver s hook clasp

Make a S hook and clasp for the chain. Bend, shape, hammer hammer hammer. Polish. Thread chain through the bail and…….


queensland agate necklace

…..it's done!

Right, not, finished yet. It's time to get some photographs for posterity and the website. This is the mind-stultifying part *sigh*. 

Many hours of photography later (insert swearing at camera, cursing at computer here too) and….

red gray queensland agate sterling silver pendant

She looks pretty neat. 


'Queensland agate necklace in sterling silver, with double link chain and handmade clasp.'

So many steps, so much work, all rolled up into one little title and promotional photo.

And several weeks later, I *finally* get her up in the shop here.

El x







Mint druzy


druzy collage.jpg


I like a bit of druzy. Do you? Here's an after dinner mint for your neck. Nom.

Here now.

El x

From start…..

queensland agate cab cabochons yellow, orange, red, green


The reason I started making jewellery was to have some way to showcase the beautiful rocks that were becoming an obsession, verging on needing intervention. I was entirely not content to leave them in a dusty display case where only myself, my family and the occasional visitor silly enough to express a vague interest could see them.  Living in Queensland, Australia, I have access to 'rough' of one of the most beautiful agates in the world - Queensland Agate. This agate is terribly originally named - it comes from Agate Creek in Queensland, and I live approximately 1740 odd kilometres away.  I'm virtually sitting right on top of it ;). The above collage is of some of the Queensland agate cabochons that have been cut either by me, my husband or my father. We all admit to the same obsession, so sadly there's no-one to implement an intervention on our behalf. It's probably too late for us all anyway!

I thought I'd give a little peek of my process from rough start to polished finish. I have a house full of equipment, with lapidary equipment out the back for the cutting of the rocks, to my own little room in the front full of awesome tools and some fire to create the setting. 

So let's start at the very beginning: a very good place to start! As I have two small children, rockhounding into the middle of Australia (unbearable heat, dirt and oh, so much whinging... not to mention no toilets or showers) isn't really do-able at this point in my life. So I frequent rock and gem shows to pick up whatever rough the local grizzled rockhounds are willing to part with.


PART 1 - FROM ROUGH ROCK TO SHINY CABOCHON

queensland agate rough

These are a couple of pieces of Queensland Agate, just as they come from the ground. Possibly a little cleaner. Innocent looking pebbles, aren't they? Who knows what beauty dwells within? Well, no-one, until we get these fellas on the slab saw.


queensland agate in slab saw

The slab saw will cut a slice through this agate to reveal what is hiding inside. Not every rock has a useable inside - big areas of bland quartz, blah colours and unattractive inclusions makes this part of the process time consuming and a LOT of rough needs to be cut before you might chance on a pretty piece, with strong, interesting, clean patterning and/or colouring. And then, a fracture line across the face can render the whole thing useless, and break a lapidarist's heart. 


slice of queensland agate

Well, looky here! This one has surely got something purty going on inside. Let's cut it again so that we have a slice with two flat sides - front and back. I'm going to fully admit that this was the 8th pebble that I cut - the first 7 were rubbish. It's all the luck of the draw. Also, please excuse my awful-looking-car-door-battered thumbnail in all of the shots. 


slice of queensland agate

Here's the resulting slice. It's not a stunner, but it's a pretty example of some of the dove gray/red material. There are so many colours in Queensland Agate, I'll share some of them with you in later posts.


shaping queensland agate rough on grinding wheels

Onto the grinding wheel it goes, to take the rind off the outside and see what's left when that's gone. Then, I generally decide on a freeform shape, whatever best suits the pattern in the stone.


queensland agate preform

With the rind gone, a teardrop shape appeared. Here's the pre-form, ready to be dopped, domed and polished.


dopped cabochons

The pre-form is dopped - attached to a stick with wax. This is to help hold the piece while it's being shaped and polished on the grinding wheels. My dad domes his cabochons without dopping them!?!  I have no idea how he doesn't take off all his fingertips! 

Now, gotta wait until that wax cools right down. Time for a coffee break…..


photo 3.jpg

……. *sip sip* Here's a picture of one of my little helpers. He's very patient, helps me sort the rocks and always gives them the taste test of approval before moving onto the next one.


doming cabochon

Slurp, coffee's done. Time to shape the dome of the cab (cabochon), moving progressively through grits from rough (100) to super-fine (3000). There's water dripping on those wheels to help lubricate the process and to prevent the stone from getting too hot.


cabochon domed and shaped

Here's the cab after the 280 grit - formed and generally smoothed. Now to move through 600, 1200 and 3000……


queensland agate cabochon at 3000 grit

 After the 3000 grit wheel, the cab is pre-polished and, because it's agate and super-hard, it's already got a pretty great shine. But that's nothing compared to what it will look like after the final polish.


polishing on a leather wheel with tin oxide

The final polish happens on a wet leather flat wheel, charged with tin oxide. There are heaps of different ways that lapidarists achieve this final polish, but this way works really well for me, especially on hard stones like agate. It gives the agate an absolutely glass-like finish, like the gloss has been poured on! This is one of the reasons that I simply adore Queensland Agate - I  am quite partial to delicious shiny sparkly things. :D


polished queensland agate

And here we are, the tin oxide and leather have done their job, and this agate is buffed to shiny deliciousness. Now, how do we get this rock off this darn wax so that I can turn it into something pretty to wear?


photo 2-2.jpg

Into the freezer it goes (hmm, might be time to throw away those frostbitten leftovers), and then, when it's cold enough……..


photo 3-2.jpg

……..POP! Off the wax it comes, complete with frosty rime.


Now, even though it's shiny and gorgeous, the rock is still not ready to be set. 

photo-2.jpg

The front and sides are shiny and smooth, but the back edge is really rough and sharp, and this will make popping the stone in and out while setting really tricky. It can prevent the stone from sitting well in the setting too. Plus, it feels yucky in the hand and makes an ugly finish, so let's knock that off. Back on the grinding wheel it goes - champfer that sharp arris off of the back edge!


photo 4-2.jpg

There, now it's lovely to touch. I also gave the back a quick polish - it won't be seen when the stone is set, but I'll know it's there. ;)

queensland agate cabochon grey gray and red

And, TA DA! A cabochon of Queensland agate, ready to be turned into a one-of-a-kind piece of jewellery. And no matter how simple the setting, every piece made with a handcut rock is unique, because no two rocks are the same!


Wanna see what comes next? Then click….

Part 2…..FROM SHINY ROCK TO WEARABLE ART.



El x

collage.jpg






Can you hear the music ring?

Music is such an essential part of most people's life, and it has a special place in mine. When I'm not stealing time from my child-wrangling duties to play in my jewellery workspace, I'm usually learning some new arias to sing at a function or gig. And with a 4 year old who keeps trying to shush me, and a 1 year old who 'sings' along, this is easier said than done.

Then one day, when Mr One year old was merrily rolling (scrunching, flattening) one of the sheets of music that of a piece I was desperately trying to learn, the idea for a music scroll ring popped into being.

1.jpg


A sheet of music that can't be scrunched and flattened.

An image forever suspended in sterling silver.

music ring colalge.jpg


A wonderful keepsake for any musician, or one who loves to keep music close at hand. So to speak ;)

Available here.

El x


The bane of my existence

When it comes to the actual photographying of my pieces, I'd sometimes rather pull my toenails out. I really want to do the stones justice, and the pesky reflections and glare and I tend to have extreme arguments. 

Well, I'm learning to diffuse properly, and while I'm still having some moments of extreme frustration, it's on the whole getting a lot better.

DSC 0427.jpg

This Australian marra mamba ring was driving me to distraction. I really wanted to show off the landscape in the stone.

And here we are, now with diffusion. 

DSC 0641A.jpg

Though it now doesn't show just how shiny it is. Hmm. Oh well, baby steps.

This baby is in the shop here.


Ellie x

Laguna Agate and Agua Nueva

These two new necklaces that I made recently have completely different stones, yet their colours are remarkably similar.

This cabochon of agua nueva is gentle with dusky pinks and pastel yellows and whites.

BLD 6986.jpg


Whereas this pretty girl of laguna agate is an almost identical shade of pastel pink.

BLD 6907.jpg


Nature is just wonderful :D. 

Both of these girls (they're definitely girls, they're both pink ;) are up in the shop here and here.

Petrified Woods


So many people love fossils, and I'm one of them, it's simply mindblowing to discover prehistoric pieces of wood that have converted entirely to hard silica.  We have a garden full of chunks of fossilised wood that are just crying out to be cut and slabbed. 

One of my very favourite cabochons is this piece of Tasmanian fossilised tree fern. 

fossiltreefern.jpg

Fossilized Tree Fern


Tasmania has great conditions for creating fossils and some of the most beautiful examples of fossilised wood in Australia come from there. This particular cabochon has gone into my collection, but here's a piece of fossilised palm wood in glorious creams and blacks that is a wearable piece of the prehistoric.


BLD 7111.jpg

Petrified palm wood pendant in sterling silver


Found here in my shop.



ellie@rocknwrap.com © E Holland 2012